Very happy to hear that.
From: David D. Johnson [mailto:***@brown.edu]
Sent: Wednesday, May 10, 2017 1:52 PM
To: xCAT Users Mailing list
Subject: Re: [xcat-user] pxe booting older hardware with newer xcat
Thanks!
I went into bios setup on one of the twelve machines, disabled UEFI and Legacy option rom for the
four PCI slots, and saved the new settings. Then I used asu show to see what changed there.
Made the same eight changes to the other eleven nodes with pasu batch, and much happier with
the reduced boot time.
Thinking that the original problem was with misconfigured serial console combined with Legacy/UEFI confusion.
A couple machines required an extra rpower reset on the first install attempt, but worked fine the second time.
Bottom line, all twelve are now back up and running after 6.8 -> 7.2 rhel update.
â ddj
On May 9, 2017, at 9:06 AM, Jarrod Johnson <***@lenovo.com<mailto:***@lenovo.com>> wrote:
I meant leaving blank, rather than setting to mac. Mac says pull from mac table, rather than using âIPAPPENDâ style which is what having no setting.
You can disable the option rom for the FC card. There are settings in asu to disable the option rom without disabling the card.
From: David D Johnson [mailto:***@brown.edu]
Sent: Tuesday, May 09, 2017 8:56 AM
To: xCAT Users Mailing list
Subject: Re: [xcat-user] pxe booting older hardware with newer xcat
Jarrod:
I would prefer to set installnic and primarynic to nothing if I can get away with it. When I get it wrong
it is messy. I used eno1 because that's what a USB-stick install ended up calling it on the same hardware
for the lan-on-motherboard port formerly known as eth0. (grumble).
Yes, I was using rcons, and it would get to the point I would expect to see PXE starting. I checked asu output,
found several things out of whack, but after fixing them all, still didn't work.
1) Mac address was for the eth1 instead of eth0 port. Fixed
2) ethernet boot config was Legacy and UEFI. I changed both ports to Legacy. The UEFI attempt has never worked,
takes a long time.
3) serial console was not configured according to best recipe, including enable redirection after POST.
I ran the asu batch script that we've had lying around (had never been run on these nodes, but I'd used it on other similar nodes)
set uEFI.ProcessorHyperThreading Disable
set uEFI.RemoteConsoleRedirection Enable
set uEFI.SerialPortSharing Enable
set uEFI.SerialPortAccessMode Dedicated
set uEFI.SPRedirection Enable
set uEFI.Com1TextEmul VT100
set uEFI.Com1ActiveAfterBoot Enable
These were the changes:
305c305
< BootOrder.BootOrder=Legacy Only=CD/DVD Rom=Floppy Disk=USB Storage=Hard Disk 0=PXE Network
---
BootOrder.BootOrder=Legacy Only=Hard Disk 0=PXE Network
309,310c309,310
< PXE.NicPortPxeMode.1=UEFI and Legacy Support
< PXE.NicPortPxeMode.2=UEFI and Legacy Support
---
PXE.NicPortPxeMode.1=Legacy Support
PXE.NicPortPxeMode.2=Legacy Support
360c360
< uEFI.RomOrder=Ethernet 1=Ethernet 2=Ethernet 3=Ethernet 4=SAS Controller=Slot 1=Slot 2=Slot 3=Slot 4
---
uEFI.RomOrder=Ethernet 1=Ethernet 2=SAS Controller=Slot 1=Slot 2=Slot 3=Slot 4
429,431c429,431
< uEFI.SerialPortSharing=Disable
< uEFI.SerialPortAccessMode=Disable
< uEFI.SPRedirection=Disable
---
uEFI.SerialPortSharing=Enable
uEFI.SerialPortAccessMode=Dedicated
uEFI.SPRedirection=Enable
437,438c437,438
< uEFI.Com1TextEmul=ANSI
< uEFI.Com1ActiveAfterBoot=Disable
---
uEFI.Com1TextEmul=VT100
uEFI.Com1ActiveAfterBoot=Enable
Setting next boot from pxe to enabled and tried booting again. No joy.
Er Tao Zhao:
I tried what you suggested, and the rinstall command worked perfectly. I could see the anaconda process on rcons.
What is it that rinstall did this time that I wasn't doing manually?
I am grateful for both of your responses, and pleased that I've gotten one of the twelve reinstalled successfully.
If there's any way I can use asu to tell the bios not to scan the two dual port FC cards, I'd love to know how.
That would save five minutes per boot!
Regards,
-- ddj
Dave Johnson
Brown University
On May 9, 2017, at 8:36 AM, Jarrod Johnson <***@lenovo.com<mailto:***@lenovo.com>> wrote:
Incidentally, I donât see why one should set installnic and primarynic to âmacâ except for PPC. In x86, we carry forward whatever mac address that happened to PXE by default, if not set to anything.
From: Er Tao Zhao [mailto:***@cn.ibm.com]
Sent: Monday, May 08, 2017 11:08 PM
To: xcat-***@lists.sourceforge.net<mailto:xcat-***@lists.sourceforge.net>
Subject: Re: [xcat-user] pxe booting older hardware with newer xcat
Hi, David
Will you pls set installnic and primarynic to 'mac', and then run rinstall to redeploy OS for the node?
Pls let us know if there is more issues.
Thx!
Best Regards,
-----------------------------------
Zhao Er Tao
IBM China System and Technology Laboratory, Beijing
Tel:(86-10)82450485<tel:(86-10)82450485>
Email: ***@cn.ibm.com<mailto:***@cn.ibm.com>
Address: 1/F, 28 Building,ZhongGuanCun Software Park,
No.8 DongBeiWang West Road, Haidian District,
Beijing, 100193, P.R.China
----- Original message -----
From: "David D. Johnson" <***@brown.edu<mailto:***@brown.edu>>
To: xCAT Users Mailing list <xcat-***@lists.sourceforge.net<mailto:xcat-***@lists.sourceforge.net>>
Cc:
Subject: [xcat-user] pxe booting older hardware with newer xcat
Date: Tue, May 9, 2017 4:28 AM
Iâm needing to reinstall / update a dozen IBM x3650-M2 servers from 2009.
These Nehalem nodes get up to the point where they should be doing PXE dhcp request, etc, but
I am only seeing blank screen. No DHCP events logged. It seems xcat would not be to blame, but
Iâm wondering if anyone else has encountered a situation like this. Tried
set BootOrder.BootOrder "Legacy Only=PXE Network"
[***@mgt5 rh]# lsdef storage005 --osimage
Object name: storage005
arch=x86_64
bmc=storage005-bmc
bmcport=0
currchain=boot
currstate=install rhels7.2-x86_64-storage
groups=storage,ipmi,storagenodes,chs,ext
initrd=xcat/osimage/rhels7.2-x86_64-install-storage/initrd.img
installnic=eno0
ip=172.20.1.5
kcmdline=quiet inst.repo=http://172.20.0.6:80/install/rhels7.2/x86_64<http://172.20.0.6/install/rhels7.2/x86_64> inst.ks=http://172.20.0.6:80/install/autoinst/storage005<http://172.20.0.6/install/autoinst/storage005> ip=eno0:dhcp inst.cmdline console=tty0 console=ttyS0,115200
kernel=xcat/osimage/rhels7.2-x86_64-install-storage/vmlinuz
mac=00:1A:64:E5:BA:56
mgt=ipmi
netboot=pxe
nfsserver=172.20.0.6
os=rhels7.2
postbootscripts=otherpkgs
postscripts=syslog,remoteshell,syncfiles,setupntp,ipoib,sitespecific
power=ipmi
primarynic=eno0
profile=storage
provmethod=rhels7.2-x86_64-install-storage
serialport=0
serialspeed=115200
status=powering-on
statustime=05-08-2017 15:46:33
tftpserver=172.20.0.6
profile=storage
osvers=rhels7.2
osarch=x86_64
osname=Linux
objtype=osimage
provmethod=install
imagetype=linux
osdistroname=rhels7.2-x86_64
I notice there is no pkglist â I tried cloning rhels7.2-x86_64-install-service and probably missed a step.
Thanks for any insight,
â ddj
Dave Johnson
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org<http://slashdot.org/>! http://sdm.link/slashdot
_______________________________________________
xCAT-user mailing list
xCAT-***@lists.sourceforge.net<mailto:xCAT-***@lists.sourceforge.net>
https://lists.sourceforge.net/lists/listinfo/xcat-user
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org<http://slashdot.org/>! http://sdm.link/slashdot_______________________________________________
xCAT-user mailing list
xCAT-***@lists.sourceforge.net<mailto:xCAT-***@lists.sourceforge.net>
https://lists.sourceforge.net/lists/listinfo/xcat-user
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org<http://slashdot.org/>! http://sdm.link/slashdot_______________________________________________
xCAT-user mailing list
xCAT-***@lists.sourceforge.net<mailto:xCAT-***@lists.sourceforge.net>
https://lists.sourceforge.net/lists/listinfo/xcat-user